Interrupts and flags management functions. More...

Collaboration diagram for Interrupts and flags management functions:

Functions
FunctionalState	DMA_GetCmdStatus (DMA_Stream_TypeDef *DMAy_Streamx)
	Returns the status of EN bit for the specified DMAy Streamx. More...

uint32_t	DMA_GetFIFOStatus (DMA_Stream_TypeDef *DMAy_Streamx)
	Returns the current DMAy Streamx FIFO filled level. More...

FlagStatus	DMA_GetFlagStatus (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_FLAG)
	Checks whether the specified DMAy Streamx flag is set or not. More...

void	DMA_ClearFlag (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_FLAG)
	Clears the DMAy Streamx's pending flags. More...

void	DMA_ITConfig (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT, FunctionalState NewState)
	Enables or disables the specified DMAy Streamx interrupts. More...

ITStatus	DMA_GetITStatus (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT)
	Checks whether the specified DMAy Streamx interrupt has occurred or not. More...

void	DMA_ClearITPendingBit (DMA_Stream_TypeDef *DMAy_Streamx, uint32_t DMA_IT)
	Clears the DMAy Streamx's interrupt pending bits. More...

Detailed Description

Interrupts and flags management functions.

 ===============================================================================
              ##### Interrupts and flags management functions #####
 ===============================================================================  
    [..]
    This subsection provides functions allowing to
      (+) Check the DMA enable status
      (+) Check the FIFO status 
      (+) Configure the DMA Interrupts sources and check or clear the flags or 
          pending bits status.  
           
    [..]
      (#) DMA Enable status:
          After configuring the DMA Stream (DMA_Init() function) and enabling 
          the stream, it is recommended to check (or wait until) the DMA Stream 
          is effectively enabled. A Stream may remain disabled if a configuration 
          parameter is wrong. After disabling a DMA Stream, it is also recommended 
          to check (or wait until) the DMA Stream is effectively disabled. 
          If a Stream is disabled while a data transfer is ongoing, the current 
          data will be transferred and the Stream will be effectively disabled 
          only after this data transfer completion.
          To monitor this state it is possible to use the following function:
        (++) FunctionalState DMA_GetCmdStatus(DMA_Stream_TypeDef* DMAy_Streamx); 
 
      (#) FIFO Status:
          It is possible to monitor the FIFO status when a transfer is ongoing 
          using the following function:
        (++) uint32_t DMA_GetFIFOStatus(DMA_Stream_TypeDef* DMAy_Streamx); 
 
      (#) DMA Interrupts and Flags:
          The user should identify which mode will be used in his application 
          to manage the DMA controller events: Polling mode or Interrupt mode. 
    
    *** Polling Mode ***
    ====================
    [..]
    Each DMA stream can be managed through 4 event Flags:
    (x : DMA Stream number )
      (#) DMA_FLAG_FEIFx  : to indicate that a FIFO Mode Transfer Error event occurred.
      (#) DMA_FLAG_DMEIFx : to indicate that a Direct Mode Transfer Error event occurred.
      (#) DMA_FLAG_TEIFx  : to indicate that a Transfer Error event occurred.
      (#) DMA_FLAG_HTIFx  : to indicate that a Half-Transfer Complete event occurred.
      (#) DMA_FLAG_TCIFx  : to indicate that a Transfer Complete event occurred .       
    [..]
    In this Mode it is advised to use the following functions:
      (+) FlagStatus DMA_GetFlagStatus(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_FLAG);
      (+) void DMA_ClearFlag(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_FLAG);

    *** Interrupt Mode ***
    ======================
    [..]
    Each DMA Stream can be managed through 4 Interrupts:

    *** Interrupt Source ***
    ========================
    [..]
      (#) DMA_IT_FEIFx  : specifies the interrupt source for the  FIFO Mode Transfer Error event.
      (#) DMA_IT_DMEIFx : specifies the interrupt source for the Direct Mode Transfer Error event.
      (#) DMA_IT_TEIFx  : specifies the interrupt source for the Transfer Error event.
      (#) DMA_IT_HTIFx  : specifies the interrupt source for the Half-Transfer Complete event.
      (#) DMA_IT_TCIFx  : specifies the interrupt source for the a Transfer Complete event. 
    [..]
    In this Mode it is advised to use the following functions:
      (+) void DMA_ITConfig(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT, FunctionalState NewState);
      (+) ITStatus DMA_GetITStatus(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT);
      (+) void DMA_ClearITPendingBit(DMA_Stream_TypeDef* DMAy_Streamx, uint32_t DMA_IT);

Function Documentation

void DMA_ClearFlag	(	DMA_Stream_TypeDef *	DMAy_Streamx,
		uint32_t	DMA_FLAG
	)

Clears the DMAy Streamx's pending flags.

Parameters

DMAy_Streamx	where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_FLAG	specifies the flag to clear. This parameter can be any combination of the following values: DMA_FLAG_TCIFx: Streamx transfer complete flag DMA_FLAG_HTIFx: Streamx half transfer complete flag DMA_FLAG_TEIFx: Streamx transfer error flag DMA_FLAG_DMEIFx: Streamx direct mode error flag DMA_FLAG_FEIFx: Streamx FIFO error flag Where x can be 0 to 7 to select the DMA Stream.

Return values

None

Definition at line 1071 of file stm32f4xx_dma.c.

Here is the caller graph for this function:

void DMA_ClearITPendingBit	(	DMA_Stream_TypeDef *	DMAy_Streamx,
		uint32_t	DMA_IT
	)

Clears the DMAy Streamx's interrupt pending bits.

Parameters

DMAy_Streamx where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.

DMA_IT

specifies the DMA interrupt pending bit to clear. This parameter can be any combination of the following values:

DMA_IT_TCIFx: Streamx transfer complete interrupt
DMA_IT_HTIFx: Streamx half transfer complete interrupt
DMA_IT_TEIFx: Streamx transfer error interrupt
DMA_IT_DMEIFx: Streamx direct mode error interrupt
DMA_IT_FEIFx: Streamx FIFO error interrupt Where x can be 0 to 7 to select the DMA Stream.

Return values

None

Definition at line 1252 of file stm32f4xx_dma.c.

FunctionalState DMA_GetCmdStatus ( DMA_Stream_TypeDef * DMAy_Streamx )

Returns the status of EN bit for the specified DMAy Streamx.

Parameters

DMAy_Streamx where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.

Note: After configuring the DMA Stream (DMA_Init() function) and enabling the stream, it is recommended to check (or wait until) the DMA Stream is effectively enabled. A Stream may remain disabled if a configuration parameter is wrong. After disabling a DMA Stream, it is also recommended to check (or wait until) the DMA Stream is effectively disabled. If a Stream is disabled while a data transfer is ongoing, the current data will be transferred and the Stream will be effectively disabled only after the transfer of this single data is finished.

Return values

Current state of the DMAy Streamx (ENABLE or DISABLE).

Definition at line 943 of file stm32f4xx_dma.c.

uint32_t DMA_GetFIFOStatus ( DMA_Stream_TypeDef * DMAy_Streamx )

Returns the current DMAy Streamx FIFO filled level.

Parameters

DMAy_Streamx where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.

Return values

The

FIFO filling state.

DMA_FIFOStatus_Less1QuarterFull: when FIFO is less than 1 quarter-full and not empty.
DMA_FIFOStatus_1QuarterFull: if more than 1 quarter-full.
DMA_FIFOStatus_HalfFull: if more than 1 half-full.
DMA_FIFOStatus_3QuartersFull: if more than 3 quarters-full.
DMA_FIFOStatus_Empty: when FIFO is empty
DMA_FIFOStatus_Full: when FIFO is full

Definition at line 977 of file stm32f4xx_dma.c.

FlagStatus DMA_GetFlagStatus	(	DMA_Stream_TypeDef *	DMAy_Streamx,
		uint32_t	DMA_FLAG
	)

Checks whether the specified DMAy Streamx flag is set or not.

Parameters

DMAy_Streamx	where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_FLAG	specifies the flag to check. This parameter can be one of the following values: DMA_FLAG_TCIFx: Streamx transfer complete flag DMA_FLAG_HTIFx: Streamx half transfer complete flag DMA_FLAG_TEIFx: Streamx transfer error flag DMA_FLAG_DMEIFx: Streamx direct mode error flag DMA_FLAG_FEIFx: Streamx FIFO error flag Where x can be 0 to 7 to select the DMA Stream.

Return values

The	new state of DMA_FLAG (SET or RESET).

Definition at line 1004 of file stm32f4xx_dma.c.

ITStatus DMA_GetITStatus	(	DMA_Stream_TypeDef *	DMAy_Streamx,
		uint32_t	DMA_IT
	)

Checks whether the specified DMAy Streamx interrupt has occurred or not.

Parameters

DMAy_Streamx	where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_IT	specifies the DMA interrupt source to check. This parameter can be one of the following values: DMA_IT_TCIFx: Streamx transfer complete interrupt DMA_IT_HTIFx: Streamx half transfer complete interrupt DMA_IT_TEIFx: Streamx transfer error interrupt DMA_IT_DMEIFx: Streamx direct mode error interrupt DMA_IT_FEIFx: Streamx FIFO error interrupt Where x can be 0 to 7 to select the DMA Stream.

Return values

The	new state of DMA_IT (SET or RESET).

Definition at line 1170 of file stm32f4xx_dma.c.

void DMA_ITConfig	(	DMA_Stream_TypeDef *	DMAy_Streamx,
		uint32_t	DMA_IT,
		FunctionalState	NewState
	)

Enables or disables the specified DMAy Streamx interrupts.

Parameters

DMAy_Streamx	where y can be 1 or 2 to select the DMA and x can be 0 to 7 to select the DMA Stream.
DMA_IT	specifies the DMA interrupt sources to be enabled or disabled. This parameter can be any combination of the following values: DMA_IT_TC: Transfer complete interrupt mask DMA_IT_HT: Half transfer complete interrupt mask DMA_IT_TE: Transfer error interrupt mask DMA_IT_FE: FIFO error interrupt mask
NewState	new state of the specified DMA interrupts. This parameter can be: ENABLE or DISABLE.

Return values

None

Definition at line 1118 of file stm32f4xx_dma.c.

Here is the caller graph for this function:

Functions

Detailed Description

Function Documentation