Synchronization management functions.
More...
Synchronization management functions.
===============================================================================
##### Synchronization management functions #####
===============================================================================
##### TIM Driver: how to use it in synchronization Mode #####
===============================================================================
[..]
*** Case of two/several Timers ***
==================================
[..]
(#) Configure the Master Timers using the following functions:
(++) void TIM_SelectOutputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_TRGOSource);
(++) void TIM_SelectMasterSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_MasterSlaveMode);
(#) Configure the Slave Timers using the following functions:
(++) void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource);
(++) void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_SlaveMode);
*** Case of Timers and external trigger(ETR pin) ***
====================================================
[..]
(#) Configure the External trigger using this function:
(++) void TIM_ETRConfig(TIM_TypeDef* TIMx, uint16_t TIM_ExtTRGPrescaler, uint16_t TIM_ExtTRGPolarity,
uint16_t ExtTRGFilter);
(#) Configure the Slave Timers using the following functions:
(++) void TIM_SelectInputTrigger(TIM_TypeDef* TIMx, uint16_t TIM_InputTriggerSource);
(++) void TIM_SelectSlaveMode(TIM_TypeDef* TIMx, uint16_t TIM_SlaveMode);
| void TIM_ETRConfig |
( |
TIM_TypeDef * |
TIMx, |
|
|
uint16_t |
TIM_ExtTRGPrescaler, |
|
|
uint16_t |
TIM_ExtTRGPolarity, |
|
|
uint16_t |
ExtTRGFilter |
|
) |
| |
Configures the TIMx External Trigger (ETR).
- Parameters
-
| TIMx | where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral. |
| TIM_ExtTRGPrescaler | The external Trigger Prescaler. This parameter can be one of the following values:
- TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF.
- TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2.
- TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4.
- TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
|
| TIM_ExtTRGPolarity | The external Trigger Polarity. This parameter can be one of the following values:
- TIM_ExtTRGPolarity_Inverted: active low or falling edge active.
- TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
|
| ExtTRGFilter | External Trigger Filter. This parameter must be a value between 0x00 and 0x0F |
- Return values
-
Definition at line 3012 of file stm32f4xx_tim.c.
| void TIM_SelectInputTrigger |
( |
TIM_TypeDef * |
TIMx, |
|
|
uint16_t |
TIM_InputTriggerSource |
|
) |
| |
Selects the Input Trigger source.
- Parameters
-
| TIMx | where x can be 1, 2, 3, 4, 5, 8, 9, 10, 11, 12, 13 or 14 to select the TIM peripheral. |
| TIM_InputTriggerSource | The Input Trigger source. This parameter can be one of the following values:
- TIM_TS_ITR0: Internal Trigger 0
- TIM_TS_ITR1: Internal Trigger 1
- TIM_TS_ITR2: Internal Trigger 2
- TIM_TS_ITR3: Internal Trigger 3
- TIM_TS_TI1F_ED: TI1 Edge Detector
- TIM_TS_TI1FP1: Filtered Timer Input 1
- TIM_TS_TI2FP2: Filtered Timer Input 2
- TIM_TS_ETRF: External Trigger input
|
- Return values
-
Definition at line 2892 of file stm32f4xx_tim.c.
| void TIM_SelectMasterSlaveMode |
( |
TIM_TypeDef * |
TIMx, |
|
|
uint16_t |
TIM_MasterSlaveMode |
|
) |
| |
Sets or Resets the TIMx Master/Slave Mode.
- Parameters
-
| TIMx | where x can be 1, 2, 3, 4, 5, 8, 9 or 12 to select the TIM peripheral. |
| TIM_MasterSlaveMode | specifies the Timer Master Slave Mode. This parameter can be one of the following values:
- TIM_MasterSlaveMode_Enable: synchronization between the current timer and its slaves (through TRGO)
- TIM_MasterSlaveMode_Disable: No action
|
- Return values
-
Definition at line 2982 of file stm32f4xx_tim.c.
| void TIM_SelectOutputTrigger |
( |
TIM_TypeDef * |
TIMx, |
|
|
uint16_t |
TIM_TRGOSource |
|
) |
| |
Selects the TIMx Trigger Output Mode.
- Parameters
-
| TIMx | where x can be 1, 2, 3, 4, 5, 6, 7 or 8 to select the TIM peripheral. |
| TIM_TRGOSource | specifies the Trigger Output source. This parameter can be one of the following values: |
- For all TIMx
- TIM_TRGOSource_Reset: The UG bit in the TIM_EGR register is used as the trigger output(TRGO)
- TIM_TRGOSource_Enable: The Counter Enable CEN is used as the trigger output(TRGO)
- TIM_TRGOSource_Update: The update event is selected as the trigger output(TRGO)
- For all TIMx except TIM6 and TIM7
- TIM_TRGOSource_OC1: The trigger output sends a positive pulse when the CC1IF flag is to be set, as soon as a capture or compare match occurs(TRGO)
- TIM_TRGOSource_OC1Ref: OC1REF signal is used as the trigger output(TRGO)
- TIM_TRGOSource_OC2Ref: OC2REF signal is used as the trigger output(TRGO)
- TIM_TRGOSource_OC3Ref: OC3REF signal is used as the trigger output(TRGO)
- TIM_TRGOSource_OC4Ref: OC4REF signal is used as the trigger output(TRGO)
- Return values
-
Definition at line 2935 of file stm32f4xx_tim.c.
| void TIM_SelectSlaveMode |
( |
TIM_TypeDef * |
TIMx, |
|
|
uint16_t |
TIM_SlaveMode |
|
) |
| |
Selects the TIMx Slave Mode.
- Parameters
-
| TIMx | where x can be 1, 2, 3, 4, 5, 8, 9 or 12 to select the TIM peripheral. |
| TIM_SlaveMode | specifies the Timer Slave Mode. This parameter can be one of the following values:
- TIM_SlaveMode_Reset: Rising edge of the selected trigger signal(TRGI) reinitialize the counter and triggers an update of the registers
- TIM_SlaveMode_Gated: The counter clock is enabled when the trigger signal (TRGI) is high
- TIM_SlaveMode_Trigger: The counter starts at a rising edge of the trigger TRGI
- TIM_SlaveMode_External1: Rising edges of the selected trigger (TRGI) clock the counter
|
- Return values
-
Definition at line 2959 of file stm32f4xx_tim.c.
Collaboration diagram for Synchronization management functions:
1.8.10 
